 |
| You are Here: Home
> HomePro Tools > HomePro LR Instructions & Warranty |
 |
|
WARNING
This tool can inflict self pinching and piercing which can cause severe
pain and injury. Please read the installation, operation and maintenance instructions before installing or operating
this tool. The Home Pro LR is not a toy. Please store this tool away from children.
|
Tool Set Up:
| • Before assembling, identify all parts as shown: |
 |
• To assemble handle, loosen pre assembled screw and lock nut on tool head. Re insert screw
through head and handle, then tighten lock nut with crescent wrench or pliers so that it is snug but not overly
tight, (See Diagram #2). |
|
|
To lock in setting tools, use the following procedure:
| A) |
Begin with setting pieces that are a correct pair. CAUTION: AN INCORRECT PAIR WILL DAMAGE SETTING
TOOLS! See Tool Replacement instructions (below). |
| B) |
Insert bottom eyelet setting tool first, (6EB), pushing it as far as allowable into bottom chamber, (See
Diagram #3). Insert and tighten thumb screw A, (the longer of the two thumb screws). Repeat procedure for
the top eyelet setting tool, (6ET), using thumb screw B, (the shorter of the two). |
|
|
Operating the  :
| • |
Load eyelet or rivet with the flanged side, (wide area), down on bottom setting tool. (See Diagram #4). |
| • |
Insert pre punched material, unless you are using the tool as only a punch,
(with punch setting tools). |
| • |
Make sure your hand and fingers are clearly out of the path of the top and bottom setting tool compression
area. |
| • |
Pull down on the handle until maximum compression occurs, generally using 10 to 40 lbs of pressure depending
on the size and material of your eyelet or rivet. |
|
|
| • |
Insert screw C with standard nut and washer D & E as shown in Diagram #5. Adjust screw by hand
to your desired level and lock down by tightening the nut. Adjusting this screw will allow you to control your
crimping of the eyelet or rivet shaft, creating space for arrows, buttons, washers or thick material. |
|
|
Tool Replacement:
| • |
Always make sure the Top setting tool code (printed on the side of the setting tool), ends with a "T"
and the Bottom setting tool ends with a "B". The first two digits of the code should ALWAYS match on
the top AND bottom setting tools, except when using decorative eyelets. Examples: use 6ET with 6EB use 4PT with
4PB etc... See Setting Tool Parts chart for entire list (below). |
| • |
For decorative eyelets, (shapes other than round), use your decorative bottom setting tool with the top setting
tool that is designed for standard eyelets of the same size. Example: use 6ET with 6DB. |
Setting Tool Parts:
| Stock # |
Description |
 |
Stock # |
Description |
| 40100 |
Home Pro LR Tool |
|
40160* |
3/16" Eyelet Top Set |
| 40110 |
Home Pro LR Tool Set |
|
40161* |
3/16" Eyelet Bottom Set |
| 40130* |
3/32" Eyelet Top Set |
|
40162 |
3/16" Punch Top Set |
| 40131* |
3/32" Eyelet Bottom Set |
|
40163 |
3/16" Punch Bottom Set |
| 40132 |
3/32" Punch Top Set |
|
40166** |
3/16" Decorative Eyelet Bottom Set |
| 40133 |
3/32" Punch Bottom Set |
|
40180 |
1/4" Eyelet Top Set |
| 40140* |
1/8" Eyelet Top Set |
|
40181 |
1/4" Eyelet Bottom Set |
| 40141* |
1/8" Eyelet Bottom Set |
|
40182 |
1/4" Punch Topset |
| 40142 |
1/8" Punch Top Set |
|
40183 |
1/4" Punch Bottom Set |
| 40143 |
1/8" Punch Bottom Set |
|
|
|
| 40144 |
1/8" Rivet Top Set |
|
* - Will fit HomePro 2 Handtool |
| 40145 |
1/8" Rivet Bottom Set |
|
** - Always use #40166 with #40160 |
Maintenance:
| • |
Place a drop of gear or motor oil by the base of the plunger and on the screw holding the handle approximately
once every 5 - 10 thousand revolutions. |
| • |
Store away from moisture. |
|
The Home Pro LR Warranty
We warrant to the original user that this product shall be free from all defects in material
or workmanship for 1 year from the date of original purchase. This warranty does not apply to any product which
has been subject to abuse, misuse, negligence or accident; nor does it apply to nonperformance incurred when
used without American Tag eyelets and rivets. Defects caused by tampering, unauthorized alteration or repairs
are not covered by this warranty. We may elect to replace the entire unit, at no extra cost to you, with the
same model or similar model, rather than repair it. The warranty period is not extended by such repair or replacement.
Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt
is made to embody the highest degree of safety in our equipment, we cannot guarantee freedom from injury. The
user assumes all risk of injury due to use. All merchandise is sold on this condition, and no representative
of the company may waive or change this policy. If a defect covered by this warranty should occur, promptly return
the product, along with: proof of purchase, a check made out to American Tag for $5.00 to cover handling and
return shipping, and a brief explanation of the problem. Send to:
American Tag Co.
2043 Saybrook Ave.
Commerce, CA 90040
Make certain that your HomePro LR tool is properly packed to avoid damage in transit to the
factory. Please allow 3 weeks for service. Please feel free to call our customer service representatives at 1-800-223-3956
with any questions. This warranty gives you specific legal rights, and you may have other legal rights that vary
from state to state. See our web site at www.americantag.net.
|
|
|
|
